Case G: reference data
Contents
Configuration
| Parameter | Value |
|---|---|
| belt | Tsuiji-matsu (Japanese black pine), trimmed to a rectangle; 74 m long (y), 2 m deep (x), 7 m tall, 1.2 m bottom gap; shading rate 81 % after pruning (data paper section 3.7) |
| Height H (m) | 7.0 |
| Depth (m) | 2.0 |
| Width (m) | 74.0 |
| gap m | 1.2 |
| Campaign | field (full scale) |
| location | Taisha-machi, Hikawa-gun, Shimane, Japan; west end of an elementary-school playground |
| Wind directions (°) | 0 |
| measurement lines | \(0.25\thinspace H\), \(0.5\thinspace H\), \(1\thinspace H\), \(2\thinspace H\), \(3\thinspace H\), \(4\thinspace H\), \(5\thinspace H\) behind the belt = x 1.75, 3.5, 7, 14, 21, 28, 35 m (\(H = 7\thinspace\mathrm{m}\)) |
| measurement heights m | 1.5, 3.0, 4.5, 6.0 |
| Points | 28 |
| Instrument | 3-D ultrasonic anemometers (KAIJO DA-600 with TR-90Tx) at four heights on a movable tower, 5 Hz, 10 min or more per line (26 Dec 2000); approach flow 120 min (28 Dec 2000) at 1.5, 3, 6, 9 m |
| Normalisation | velocity_ratio = \(U/U_H\) and k_ratio = \(k/U_H^2\), \(U_H\) = the mean wind speed at 7 m during each measurement period (interpolated with the approach flow's power law, index 0.22); nothing is published in m/s |
| approach flow normalisation | AF_caseG.csv is \(U/U_b\) and \(k/U_b^2\) with \(U_b\) = \(U\) at 9 m; divide by \(U_H/U_b\) = 0.946 (power law 0.22) for the table's normalisation |
| Scale, note | full scale: a field observation, there is no model |
Nomenclature: symbols, columns and scores
Geometry, reference scales and release
- \(H\), \(b\), \(D\) (m) — height of the building, cube, tower or tree belt; width of the building; edge of the cubes of Case C: the lengths the cases are drawn and normalised by
- \(U_H\) (m/s) — reference speed: the mean approach-flow speed at the height \(H\) (each Data page gives the value used)
- \(U_R\), \(H_R\), \(Z_R\) (m/s, m) — reference speed and height of a workbook: Case E, \(U_R\) at \(Z_R\) = 250 m full scale (1 m in the model); Case M, \(U_R\) and \(H_R\) at the reference point of the tunnel and of each field run
- \(U_{\mathrm{ref}}\), \(L_{\mathrm{ref}}\) (m/s, m) — reference speed and length of a case’s normalisation: \(U_H\) and \(H\) (\(U_R\) and \(H_R\) in Case M); for the velocity ratios the approach speed at 15.9 m (Case E) or at 500 m (Case F)
- \(U_b\) (m/s) — Case G: mean approach-flow speed at 9 m, the normalisation of its approach-flow table
- \(q\), \(c_{\mathrm{gas}}\) (m³/s, ppm) — tracer release of the experiment: volume flow of the released gas, and its tracer content (\(10^6\) ppm when pure); \(Q\) is the source strength given to a solve
- \(R_b\) (dimensionless) — bulk Richardson number of the heated-floor cases J and L (negative: unstable stratification)
- \(\mathrm{Re_H}\), \(\mathrm{Re_D}\) (dimensionless) — Reynolds numbers \(U_H H/\nu\) and \(U_H D/\nu\) (\(\nu\): kinematic viscosity of air)
- \(u_\ast\), \(z_0\), \(\kappa\) (m/s, mm, dimensionless) — friction velocity and roughness length of the log law fitted to the approach flow, and the von Kármán constant (0.41)
- \(\mathrm{WD}\) (column
wind_direction_deg; °) — wind direction (each frame says how it is counted); \(\mathrm{WD_R}\) is the mean direction of a field run at its reference point (Case M) - \(x\), \(y\), \(z\) (columns
x,y,z; m) — coordinates in the case’s frame (\(+x\), \(+y\) and \(+z\) are the positive directions; each Data page says which way \(+x\) points), \(z\) up from the floor of the tunnel or from the ground - \(\mathrm{d}x\) (m) — lattice spacing of the OpenLB and FluidX3D runs, in metres or as a fraction of \(H\) (\(H/64\))
- \(L_r\) (m) — reattachment length behind the building, read from a wake line at ground level; reported as \(L_r/H\)
Velocity and turbulence
- \(U\), \(V\), \(W\) (columns
U,V,W; m/s) — mean velocity along \(+x\), \(+y\), \(+z\); \(V\) is positive toward \(+y\) in every case - \(\lvert\mathbf{U}\rvert\) (m/s) — magnitude of the mean velocity vector, \(\sqrt{U^2+V^2+W^2}\)
- \(V_{\mathrm{s}}\) (column
Vs; m/s) — mean omnidirectional scalar speed of a thermistor (never a vector magnitude) - \(\overline{u'u'}\), \(\overline{v'v'}\), \(\overline{w'w'}\) (columns
uu,vv,ww; m²/s²) — velocity variances (overbar: time average, prime: fluctuation about it) - \(\overline{u'v'}\), \(\overline{u'w'}\), \(\overline{v'w'}\) (columns
uv,uw,vw; m²/s²) — Reynolds shear stresses - \(k = \tfrac{1}{2}\left(\overline{u'u'}+\overline{v'v'}+\overline{w'w'}\right)\) (column
k; m²/s²) — turbulent kinetic energy - \(U/U_{\mathrm{ref}}\) (column
velocity_ratio; dimensionless) — mean speed over the case’s reference speed (\(V_{\mathrm{s}}/U_{\mathrm{ref}}\) for a thermistor) - \(\sigma_{U/U_{\mathrm{ref}}}\) (column
velocity_ratio_sd; dimensionless) — standard deviation ofvelocity_ratioover the observations behind a field value (Case F) - \(k/U_{\mathrm{ref}}^2\) (column
k_ratio; dimensionless) — turbulent kinetic energy over the square of the reference speed, where only normalised values are published (Case G)
Concentration and temperature
- \(C\) (column
C; ppm) — mean tracer-gas concentration as published (volume fraction \(\times 10^6\) of the released gas diluted in air) - \(c_{\mathrm{rms}}\) (column
c_rms; ppm) — root mean square of the concentration fluctuation - \(c_0\) (ppm) — reference concentration, defined for each case on its Data page: \(c_0 = \dfrac{c_{\mathrm{gas}}\thinspace q}{U_H H^2}\) (\(U_R H_R^2\) in the denominator in Case M)
- \(c^\ast\) (column
concentration_ratio; dimensionless) — dimensionless concentration \(c^\ast = C/c_0\); the value of a solve is \(c\thinspace U_H H^2/Q\) for its mean concentration \(c\) and its source strength \(Q\) - \(\mathrm{Sc_t}\) (dimensionless) — turbulent Schmidt number of a solve (0.3, 0.5 and 0.7)
- \(T\), \(T_{\mathrm{rms}}\) (columns
T,T_rms; °C, K) — mean air temperature as published (Cases J and L) and the root mean square of its fluctuation - \(\overline{u'c'}\), \(\overline{v'c'}\), \(\overline{w'c'}\) (columns
uc,vc,wc; ppm·m/s) — turbulent concentration fluxes - \(\overline{u'\theta'}\), \(\overline{v'\theta'}\), \(\overline{w'\theta'}\) (columns
uT,vT,wT; K·m/s) — turbulent heat fluxes (\(\theta'\): the temperature fluctuation) - \(\theta = \dfrac{T_f - T}{T_f - T_H}\) (dimensionless) — floor-referenced temperature the solves of Cases J and L are scored on: 0 at the floor, 1 in the approach air at \(H\); \(T_f\) is the floor temperature and \(T_H\) the temperature of the approach flow at \(H\)
Scores
- \(n\) — number of pairs of a measured value \(o_i\) and a modelled value \(p_i\) at one point
- \(R\) — Pearson correlation coefficient of the pairs
- \(R^2\) — square of \(R\): share of the measured variance a linear fit to the model explains
- \(\mathrm{FAC2}\) — fraction of pairs with \(0.5 \le p_i/o_i \le 2\)
- \(\mathrm{FB}\) — fractional bias \(2(\overline{o}-\overline{p})/(\overline{o}+\overline{p})\), positive when the model is low
- \(\mathrm{HR}\) (hit rate) — fraction of pairs with \(\lvert p_i-o_i\rvert/\lvert o_i\rvert \le \delta_{\mathrm{rel}}\) or \(\lvert p_i-o_i\rvert \le \delta_{\mathrm{abs}}\), where \(\delta_{\mathrm{rel}} = 0.25\) and \(\delta_{\mathrm{abs}} = 0.05\thinspace U_H\) for a velocity component
- \(\mathrm{NMSE} = \dfrac{\overline{(o-p)^2}}{\overline{o}\thinspace \overline{p}}\) — normalised mean square error
- \(\mathrm{NAD} = \dfrac{\overline{\lvert o-p\rvert}}{\overline{o}+\overline{p}}\) — normalised absolute difference
- \(\mathrm{MG} = \exp\overline{(\ln o-\ln p)}\) — geometric mean bias
- \(\mathrm{VG} = \exp\overline{(\ln o-\ln p)^2}\) — geometric variance
- The ratio of \(\mathrm{FAC2}\) keeps its sign, so a model of the other sign than the measurement is a miss; \(\mathrm{FB}\), \(\mathrm{NMSE}\) and \(\mathrm{NAD}\) divide by the means, so they are undefined (shown as —) for a signed component unless the measured and the modelled mean are both positive
- VDI 3783-9 calls the hit rate \(q\) and the tolerances \(D\) and \(W\); on this site those letters keep their other meanings (\(q\) the tracer release rate, \(D\) the block size of Case C, \(W\) the vertical velocity)
- The detection limit of a concentration is one value per case, \(10^{-3}\) of the largest measured value. It sets \(\delta_{\mathrm{abs}}\) of the hit rate and the both-below rule of \(\mathrm{FAC2}\), and floors the values in \(\mathrm{MG}\) and \(\mathrm{VG}\).
- The scores \(\mathrm{FB}\), \(\mathrm{FAC2}\), \(\mathrm{NMSE}\), \(\mathrm{NAD}\), \(\mathrm{MG}\) and \(\mathrm{VG}\) follow Chang & Hanna (2004); the hit rate follows VDI 3783-9.
Quantities scored
- \(U\), \(V\) and \(W\) (mean velocity components) over \(U_H\)
- \(k\) (turbulent kinetic energy) over \(U_H^2\)
- the speed \(\lvert\mathbf{U}\rvert\) and \(\sqrt{\lvert\mathbf{U}\rvert^2+2k}\), against a thermistor’s \(V_{\mathrm{s}}\)
- \(c^\ast = C/c_0\) (dimensionless concentration) at turbulent Schmidt numbers \(\mathrm{Sc_t}\) of 0.3, 0.5 and 0.7
- \(\theta\) (floor-referenced temperature)
Frame and units
| Property | Definition |
|---|---|
| Origin | the leeward face of the tree belt at ground level, on the vertical section through the belt's centre |
| x | \(+x\) downwind: the belt occupies \(x \in \lbrack -2,\thinspace 0\rbrack\thinspace\mathrm{m}\), the measurement lines lie behind it at \(x = 1.75\thinspace\ldots\thinspace 35\thinspace\mathrm{m}\) |
| y | \(+y\) along the belt (\(y \in \lbrack -37,\thinspace 37\rbrack\thinspace\mathrm{m}\)); every point is on \(y = 0\) |
| z | \(+z\) up; the belt spans \(z \in \lbrack 1.2,\thinspace 7\rbrack\thinspace\mathrm{m}\); points at \(z = 1.5,\thinspace 3,\thinspace 4.5,\thinspace 6\thinspace\mathrm{m}\) |
| Wind direction convention | one direction, toward \(+x\) (perpendicular to the belt); the field wind's angle to the belt normal is not published |
| Lateral sign applied | 1 |
| Coordinate scale applied | 1.0 |
| Unit of length | m (full scale) |
| Unit of \(U/U_{\mathrm{ref}}\) | dimensionless, \(U/U_H\) |
| Unit of \(k/U_{\mathrm{ref}}^2\) | dimensionless, \(k/U_H^2\) |
Reference data
Source in this repository: raw/cases/case-g/RS_caseG.csv (approach flow: raw/cases/case-g/AF_caseG.csv).
The cleaned table has 28 rows over 28 distinct points; columns point_id, config, instrument, wind_direction_deg, x, y, z, velocity_ratio, campaign, k_ratio.
| Configuration | Points |
|---|---|
| default, field, sonic anemometer, WD 0° | 28 |
Columns
The columns of the cleaned table (points.csv, points.json), in order.
The 10 columns and what each holds
| Column | Symbol | Meaning |
|---|---|---|
point_id | the tunnel's own measurement point number | |
config | configuration key: 'default', Case C centre building '0D'/'1D'/'2D', Case E state 'bc' (before) / 'ac' (after construction) | |
instrument | 'split_fibre' (vector components) or 'thermistor' (omnidirectional scalar speed) | |
wind_direction_deg | AIJ wind direction in degrees; 0 is the case's reference direction (see frame) | |
x | m, case frame | |
y | m, case frame | |
z | m above ground, case frame | |
velocity_ratio | \(U/U_{\mathrm{ref}}\) | dimensionless, mean speed over the case's reference speed (Case E: \(V_{\mathrm{s}}/U(15.9\text{ m})\), \(U(15.9\text{ m})\) = 3.935 m/s; see the case's normalisation) |
campaign | 'wind_tunnel' (model scale) or 'field' (a full-scale observation: Cases F, G, M) | |
k_ratio | \(k/U_{\mathrm{ref}}^2\) | \(k/U_{\mathrm{ref}}^2\) where the dataset publishes only normalised values (Case G; \(U_{\mathrm{ref}}\) = \(U\) at the tree height) |
Inflow
| Property | Value |
|---|---|
| Method | power law on the four published heights (1.5, 3, 6, 9 m) of \(U/U_b\); the readme states the index 0.22 |
| power law index fitted | 0.2073 |
| power law index stated | 0.22 |
| \(U_H\) over \(U_b\) power law 0.22 | 0.9462 |
| \(U_H\) over \(U_b\) log interpolation | 0.938 |
| Note | derived during cleaning, not published as a fit; the profile carries 2 decimals, so the fitted index is good to about +/-0.01 |
Known data issues
- FIELD data: full-scale metres, no model, and nothing in m/s. The table carries \(U/U_H\) (
velocity_ratio) and \(k/U_H^2\) (k_ratio), \(U_H\) = the mean speed at 7 m during each period; the approach-flow table carries \(U/U_b\) and \(k/U_b^2\) (\(U_b\) = \(U\) at 9 m) in its \(U\) and \(k\) columns, which are dimensionless here. - The readme lists the heights of the lee measurement as 1.5, 3.0, 6.0, 9.0 m; the table, the workbook, the drawing and the data paper have 1.5, 3, 4.5, 6 m.
- The tree belt is a porous canopy (shading rate 81 % after pruning): the served geometry is its 2 m × 74 m × 7 m envelope with the 1.2 m gap, and a solver needs a canopy (drag) model.
- The approach profile (28 Dec 2000, 120 min) and the lee measurements (26 Dec 2000, 10 min or more) are from different days. Behind the belt \(k/U_H^2\) is 0.040-0.072 at \(5\thinspace H\), 3-8 times below the approach flow's 0.26-0.31 at the same heights; the files do not say why.
- Only 28 numbers per quantity exist, on one centre section, one time-average each, with no repeats and no uncertainty.
- The wind direction relative to the belt normal during the measurement is not published; the case is two-dimensional by assumption.
API
| Resource | Endpoint |
|---|---|
| Case | /api/cases/G.json |
| Points (JSON) | /api/cases/G/points.json |
| Points (CSV) | /api/cases/G/points.csv |
| Approach flow (CSV) | /api/cases/G/approach_flow.csv |
| Geometry | /api/cases/G/geometry.json |
| Geometry (STL) | /api/cases/G/geometry.stl |
| Validation | /api/cases/G/validation.json |
Attribution
- Data collected by Yasuo Kurotani (Shimane University) and Nobuyoshi Kiyota (Hiroshima Institute of Technology).
- Edited and distributed by Yoshihide Tominaga (Niigata Institute of Technology), Hideki Kikumoto (The University of Tokyo) and Tsubasa Okaze (Institute of Science Tokyo).
- DOI: 10.5281/zenodo.15589666
- Citation requested: Kurotani, Y., Kiyota, N., Kobayashi, S. (2001). Windbreak effect of Tsuijimatsu in Izumo Part. 2. Summaries of technical papers of Annual Meeting, Architectural Institute of Japan, D-2 Environmental engineering II, 745-746 (in Japanese).
- Licence: CC BY 4.0
Cite
APA
Kurotani, Y., Kiyota, N., Tominaga, Y., Kikumoto, H., & Okaze, T. (2025). AIJ UWE Benchmark Dataset – Case G (Tree): Field Observation for Flow behind Tree Belt [Data set]. Zenodo. https://doi.org/10.5281/zenodo.15589666
BibTeX
@misc{aijuwe_case_g,
author = "Kurotani, Yasuo and Kiyota, Nobuyoshi and Tominaga, Yoshihide and Kikumoto, Hideki and Okaze, Tsubasa",
title = "{AIJ UWE Benchmark Dataset -- Case G (Tree): Field Observation for Flow behind Tree Belt}",
year = "2025",
publisher = "Zenodo",
doi = "10.5281/zenodo.15589666",
url = "https://doi.org/10.5281/zenodo.15589666",
note = "Data set"
}
API: see About.