Case L: reference data

Contents
  1. Configuration
  2. Frame and units
  3. Reference data
  4. Columns
  5. Inflow
  6. Known data issues
  7. API
  8. Attribution
    1. Cite

Configuration

Parameter Value
Array 14 rows (along x) by 9 columns (across y) of cubes, \(H = 0.06\thinspace\mathrm{m}\), pitch 0.12 m (street width = H, plan area ratio 25 %), published as BD_caseL.stl; the data paper calls it '9 rows by 14 columns'
Height H (m) 0.06
pitch m 0.12
cubes 126
Reynolds number \(\mathrm{Re_H}\) 5600
\(U_H\) (m/s) 1.339415
Wind directions (°) 0
Measurement planes 8 heights (4 .. 150 mm) at 27 locations in the streets near the source, 4 heights (70 .. 150 mm) at 14 locations above the blocks, 3 heights (4 .. 30 mm) at 24 locations around
Points 344
stratification unstable: floor 45.0 degC, air at \(z = H\) 14.75 degC (difference 30.3 K), bulk Richardson number -0.035 (workbook; the readme says -0.04); the workbook gives the building surface as 42.2 degC
source floor line source across the tunnel at \(x = -0.15\thinspace\mathrm{m}\) between rows 7 and 8: readme 0.037 m x 1.2 m, BD_caseL.stl patch 0.04 m x 1.02 m; 100 % ethylene, 8.33e-6 m³/s (500 cc/min) at 35 degC
concentration normalisation \(c_0 = \dfrac{q}{U_H H^2}\) = 1728.23 ppm (the workbook's value)
Instrument split-fibre hot wire (velocity), cold wire (temperature), high-speed hydrocarbon analyser (concentration), 1000 Hz with a 200 Hz low-pass filter, 60 s per point
Wind tunnel thermally stratified wind tunnel, Tokyo Polytechnic University (Atsugi); 1.2 m wide, 1.0 m high; 26 aluminium angles 9 mm high every 200 mm as roughness; model floor 10 mm above the tunnel floor
Scale, note model scale; the sources state no model:full scale ratio
Nomenclature: symbols, columns and scores

Geometry, reference scales and release

  • \(H\), \(b\), \(D\) (m) — height of the building, cube, tower or tree belt; width of the building; edge of the cubes of Case C: the lengths the cases are drawn and normalised by
  • \(U_H\) (m/s) — reference speed: the mean approach-flow speed at the height \(H\) (each Data page gives the value used)
  • \(U_R\), \(H_R\), \(Z_R\) (m/s, m) — reference speed and height of a workbook: Case E, \(U_R\) at \(Z_R\) = 250 m full scale (1 m in the model); Case M, \(U_R\) and \(H_R\) at the reference point of the tunnel and of each field run
  • \(U_{\mathrm{ref}}\), \(L_{\mathrm{ref}}\) (m/s, m) — reference speed and length of a case’s normalisation: \(U_H\) and \(H\) (\(U_R\) and \(H_R\) in Case M); for the velocity ratios the approach speed at 15.9 m (Case E) or at 500 m (Case F)
  • \(U_b\) (m/s) — Case G: mean approach-flow speed at 9 m, the normalisation of its approach-flow table
  • \(q\), \(c_{\mathrm{gas}}\) (m³/s, ppm) — tracer release of the experiment: volume flow of the released gas, and its tracer content (\(10^6\) ppm when pure); \(Q\) is the source strength given to a solve
  • \(R_b\) (dimensionless) — bulk Richardson number of the heated-floor cases J and L (negative: unstable stratification)
  • \(\mathrm{Re_H}\), \(\mathrm{Re_D}\) (dimensionless) — Reynolds numbers \(U_H H/\nu\) and \(U_H D/\nu\) (\(\nu\): kinematic viscosity of air)
  • \(u_\ast\), \(z_0\), \(\kappa\) (m/s, mm, dimensionless) — friction velocity and roughness length of the log law fitted to the approach flow, and the von Kármán constant (0.41)
  • \(\mathrm{WD}\) (column wind_direction_deg; °) — wind direction (each frame says how it is counted); \(\mathrm{WD_R}\) is the mean direction of a field run at its reference point (Case M)
  • \(x\), \(y\), \(z\) (columns x, y, z; m) — coordinates in the case’s frame (\(+x\), \(+y\) and \(+z\) are the positive directions; each Data page says which way \(+x\) points), \(z\) up from the floor of the tunnel or from the ground
  • \(\mathrm{d}x\) (m) — lattice spacing of the OpenLB and FluidX3D runs, in metres or as a fraction of \(H\) (\(H/64\))
  • \(L_r\) (m) — reattachment length behind the building, read from a wake line at ground level; reported as \(L_r/H\)

Velocity and turbulence

  • \(U\), \(V\), \(W\) (columns U, V, W; m/s) — mean velocity along \(+x\), \(+y\), \(+z\); \(V\) is positive toward \(+y\) in every case
  • \(\lvert\mathbf{U}\rvert\) (m/s) — magnitude of the mean velocity vector, \(\sqrt{U^2+V^2+W^2}\)
  • \(V_{\mathrm{s}}\) (column Vs; m/s) — mean omnidirectional scalar speed of a thermistor (never a vector magnitude)
  • \(\overline{u'u'}\), \(\overline{v'v'}\), \(\overline{w'w'}\) (columns uu, vv, ww; m²/s²) — velocity variances (overbar: time average, prime: fluctuation about it)
  • \(\overline{u'v'}\), \(\overline{u'w'}\), \(\overline{v'w'}\) (columns uv, uw, vw; m²/s²) — Reynolds shear stresses
  • \(k = \tfrac{1}{2}\left(\overline{u'u'}+\overline{v'v'}+\overline{w'w'}\right)\) (column k; m²/s²) — turbulent kinetic energy
  • \(U/U_{\mathrm{ref}}\) (column velocity_ratio; dimensionless) — mean speed over the case’s reference speed (\(V_{\mathrm{s}}/U_{\mathrm{ref}}\) for a thermistor)
  • \(\sigma_{U/U_{\mathrm{ref}}}\) (column velocity_ratio_sd; dimensionless) — standard deviation of velocity_ratio over the observations behind a field value (Case F)
  • \(k/U_{\mathrm{ref}}^2\) (column k_ratio; dimensionless) — turbulent kinetic energy over the square of the reference speed, where only normalised values are published (Case G)

Concentration and temperature

  • \(C\) (column C; ppm) — mean tracer-gas concentration as published (volume fraction \(\times 10^6\) of the released gas diluted in air)
  • \(c_{\mathrm{rms}}\) (column c_rms; ppm) — root mean square of the concentration fluctuation
  • \(c_0\) (ppm) — reference concentration, defined for each case on its Data page: \(c_0 = \dfrac{c_{\mathrm{gas}}\thinspace q}{U_H H^2}\) (\(U_R H_R^2\) in the denominator in Case M)
  • \(c^\ast\) (column concentration_ratio; dimensionless) — dimensionless concentration \(c^\ast = C/c_0\); the value of a solve is \(c\thinspace U_H H^2/Q\) for its mean concentration \(c\) and its source strength \(Q\)
  • \(\mathrm{Sc_t}\) (dimensionless) — turbulent Schmidt number of a solve (0.3, 0.5 and 0.7)
  • \(T\), \(T_{\mathrm{rms}}\) (columns T, T_rms; °C, K) — mean air temperature as published (Cases J and L) and the root mean square of its fluctuation
  • \(\overline{u'c'}\), \(\overline{v'c'}\), \(\overline{w'c'}\) (columns uc, vc, wc; ppm·m/s) — turbulent concentration fluxes
  • \(\overline{u'\theta'}\), \(\overline{v'\theta'}\), \(\overline{w'\theta'}\) (columns uT, vT, wT; K·m/s) — turbulent heat fluxes (\(\theta'\): the temperature fluctuation)
  • \(\theta = \dfrac{T_f - T}{T_f - T_H}\) (dimensionless) — floor-referenced temperature the solves of Cases J and L are scored on: 0 at the floor, 1 in the approach air at \(H\); \(T_f\) is the floor temperature and \(T_H\) the temperature of the approach flow at \(H\)

Scores

  • \(n\) — number of pairs of a measured value \(o_i\) and a modelled value \(p_i\) at one point
  • \(R\) — Pearson correlation coefficient of the pairs
  • \(R^2\) — square of \(R\): share of the measured variance a linear fit to the model explains
  • \(\mathrm{FAC2}\) — fraction of pairs with \(0.5 \le p_i/o_i \le 2\)
  • \(\mathrm{FB}\) — fractional bias \(2(\overline{o}-\overline{p})/(\overline{o}+\overline{p})\), positive when the model is low
  • \(\mathrm{HR}\) (hit rate) — fraction of pairs with \(\lvert p_i-o_i\rvert/\lvert o_i\rvert \le \delta_{\mathrm{rel}}\) or \(\lvert p_i-o_i\rvert \le \delta_{\mathrm{abs}}\), where \(\delta_{\mathrm{rel}} = 0.25\) and \(\delta_{\mathrm{abs}} = 0.05\thinspace U_H\) for a velocity component
  • \(\mathrm{NMSE} = \dfrac{\overline{(o-p)^2}}{\overline{o}\thinspace \overline{p}}\) — normalised mean square error
  • \(\mathrm{NAD} = \dfrac{\overline{\lvert o-p\rvert}}{\overline{o}+\overline{p}}\) — normalised absolute difference
  • \(\mathrm{MG} = \exp\overline{(\ln o-\ln p)}\) — geometric mean bias
  • \(\mathrm{VG} = \exp\overline{(\ln o-\ln p)^2}\) — geometric variance
  • The ratio of \(\mathrm{FAC2}\) keeps its sign, so a model of the other sign than the measurement is a miss; \(\mathrm{FB}\), \(\mathrm{NMSE}\) and \(\mathrm{NAD}\) divide by the means, so they are undefined (shown as —) for a signed component unless the measured and the modelled mean are both positive
  • VDI 3783-9 calls the hit rate \(q\) and the tolerances \(D\) and \(W\); on this site those letters keep their other meanings (\(q\) the tracer release rate, \(D\) the block size of Case C, \(W\) the vertical velocity)
  • The detection limit of a concentration is one value per case, \(10^{-3}\) of the largest measured value. It sets \(\delta_{\mathrm{abs}}\) of the hit rate and the both-below rule of \(\mathrm{FAC2}\), and floors the values in \(\mathrm{MG}\) and \(\mathrm{VG}\).
  • The scores \(\mathrm{FB}\), \(\mathrm{FAC2}\), \(\mathrm{NMSE}\), \(\mathrm{NAD}\), \(\mathrm{MG}\) and \(\mathrm{VG}\) follow Chang & Hanna (2004); the hit rate follows VDI 3783-9.

Quantities scored

  • \(U\), \(V\) and \(W\) (mean velocity components) over \(U_H\)
  • \(k\) (turbulent kinetic energy) over \(U_H^2\)
  • the speed \(\lvert\mathbf{U}\rvert\) and \(\sqrt{\lvert\mathbf{U}\rvert^2+2k}\), against a thermistor’s \(V_{\mathrm{s}}\)
  • \(c^\ast = C/c_0\) (dimensionless concentration) at turbulent Schmidt numbers \(\mathrm{Sc_t}\) of 0.3, 0.5 and 0.7
  • \(\theta\) (floor-referenced temperature)

Frame and units

Property Definition
Origin bottom centre of the windward wall of the 9th row (of 14) of the central column: \(x = 0\) is that wall, \(y = 0\) the centre line of the central column
x \(+x\) streamwise (the wind blows toward \(+x\)); row \(k\) spans x in [0.12 (\(k\)-9), 0.12 (\(k\)-9) + 0.06], so the array spans \(x \in \lbrack -0.96,\thinspace 0.66\rbrack\)
y \(+y\) lateral; column centres at \(y = 0\), +-0.12, … +-0.48 (the array spans \(y \in \lbrack -0.51,\thinspace 0.51\rbrack\))
z \(+z\) up from the model floor; cube tops at \(z = 0.06\); heated floor at \(z = 0\)
Lateral sign applied 1
Coordinate scale applied 1.0
Unit of length m (model scale)
Unit of velocity m/s
Unit of variance m²/s²
Unit of \(k\) m²/s²
Unit of concentration ppm of the released ethylene
Unit of temperature degC (T); K (\(T_{\mathrm{rms}}\)); heat fluxes K m/s; concentration fluxes ppm m/s

Reference data

Source in this repository: raw/cases/case-l/RS_caseL.csv (approach flow: raw/cases/case-l/AF_caseL.csv).

The cleaned table has 344 rows over 344 distinct points; columns point_id, config, instrument, wind_direction_deg, x, y, z, U, V, W, uu, vv, ww, k, campaign, uv, uw, C, c_rms, concentration_ratio, T, T_rms, uc, vc, wc, uT, vT, wT.

Configuration Points
default, wind tunnel, split fibre, WD 0° 344

Columns

The columns of the cleaned table (points.csv, points.json), in order.

The 28 columns and what each holds
Column Symbol Meaning
point_id   the tunnel's own measurement point number
config   configuration key: 'default', Case C centre building '0D'/'1D'/'2D', Case E state 'bc' (before) / 'ac' (after construction)
instrument   'split_fibre' (vector components) or 'thermistor' (omnidirectional scalar speed)
wind_direction_deg   AIJ wind direction in degrees; 0 is the case's reference direction (see frame)
x   m, case frame
y   m, case frame
z   m above ground, case frame
U \(U\) m/s, mean velocity along \(+x\)
V \(V\) m/s, mean velocity along \(+y\) (sign unified: positive toward \(+y\))
W \(W\) m/s, mean velocity along \(+z\)
uu \(\overline{u'u'}\) m²/s², variance of u
vv \(\overline{v'v'}\) m²/s², variance of v
ww \(\overline{w'w'}\) m²/s², variance of w
k \(k\) m²/s², turbulent kinetic energy
campaign   'wind_tunnel' (model scale) or 'field' (a full-scale observation: Cases F, G, M)
uv \(\overline{u'v'}\) m²/s², Reynolds shear stress <u'v'> as published
uw \(\overline{u'w'}\) m²/s², Reynolds shear stress <u'w'> as published
C \(C\) ppm, mean tracer-gas concentration as published (volume fraction x 1e6 of the released gas diluted in air)
c_rms \(c_{\mathrm{rms}}\) ppm, rms of the concentration fluctuation
concentration_ratio \(c^\ast\) \(C/c_0\), \(c_0 = \dfrac{q}{U_{\mathrm{ref}} L_{\mathrm{ref}}^2}\) as the benchmark defines it for the case (manifest cases.<id>.normalisation)
T \(T\) degC, mean air temperature as published (Cases J, L)
T_rms \(T_{\mathrm{rms}}\) K, rms of the temperature fluctuation
uc \(\overline{u'c'}\) ppm m/s, turbulent concentration flux <u'c'>
vc \(\overline{v'c'}\) ppm m/s, turbulent concentration flux <v'c'>
wc \(\overline{w'c'}\) ppm m/s, turbulent concentration flux <w'c'>
uT \(\overline{u'\theta'}\) K m/s, turbulent heat flux <u'theta'>
vT \(\overline{v'\theta'}\) K m/s, turbulent heat flux <v'theta'>
wT \(\overline{w'\theta'}\) K m/s, turbulent heat flux <w'theta'>

Inflow

Property Value
Method least squares, \(\kappa\) = 0.41, \(z = 0.02\thinspace\ldots\thinspace 0.32\thinspace\mathrm{m}\) (about \(5\thinspace H\)) on the workbook's Inflow sheet (CSV = its rounding)
Friction velocity \(u_\ast\) (m/s) 0.06999
Roughness length \(z_0\) (mm) 0.0265
\(U_H\), measured (m/s) 1.3394
Log-law error at H -1.6 %
log law rms residual 2.2 %
Note derived during scoping, not published by AIJ; the boundary layer is unstably stratified, so a neutral log law is only a rough description

Known data issues

  • RS_caseL.csv's temperature column is headed 'T(K)' but holds DEGREES CELSIUS (12.85 .. 29.86); AF_caseL.csv's 'T(K)' is kelvin (283 .. 295). The API serves degrees Celsius for both.
  • The published CSV is the workbook rounded to 2-4 decimals; the table is rebuilt from the workbook. Its 'tc' column (temperature-concentration covariance, K ppm) and the workbook's 'Usc' (the vector magnitude of the mean velocity) are not in the table.
  • BD_caseL.stl: the two bottom triangles (\(z = 0\)) of each of the 126 cubes (252 triangles) are wound inward; the served geometry.stl is the 126 boxes, outward.
  • The readme's file list names AF_caseK.csv and RS_caseK.csv; the files are AF_caseL.csv and RS_caseL.csv.
  • The readme's 'building surface temperature \(T_b\) = 14.8 degC' is the approach-flow air temperature at \(z = H\); the workbook gives the building surface as 42.2 degC.
  • The line source is 0.037 m x 1.2 m in the readme and data paper but a 0.04 m x 1.02 m patch in BD_caseL.stl.
  • The \(+y\) and -y halves are not mirror images: the same point differs in \(U\) by 26 %, in \(k\) by 23 %, in C by 36 % on average, and \(U\) is 0.11 m/s lower and T 1.3 K higher at \(+y\) at \(z = 0.15\thinspace\mathrm{m}\) (0.09 m above the roofs), so the tunnel flow has a lateral gradient; do not assume symmetry.
  • The workbook carries no expanded uncertainty (the data paper mentions one for Case J only).
  • AF_caseL.csv lists the profile from the top (\(z = 0.32\thinspace\mathrm{m}\)) down and has no \(k\).
  • The measured tracer flux through the cross-sections equals q / 1.2 m to 0.86 .. 1.0 (street and cube-column lines averaged), which fixes q and the unit ppm; the cube-column line alone carries only 0.2 .. 0.4 of it.

API

Attribution

  • Data collected by Ryuichiro Yoshie (Tokyo Polytechnic University) and Koudai Katada (Tokyo Polytechnic University).
  • Edited and distributed by Yoshihide Tominaga (Niigata Institute of Technology), Hideki Kikumoto (The University of Tokyo) and Tsubasa Okaze (Institute of Science Tokyo).
  • DOI: 10.5281/zenodo.15487637
  • Citation requested: Yoshie, R., Nomura, K., Katada, K., Jiang, G. (2012). Non-isothermal large eddy simulation of pollutant and thermal dispersion in urban street canyons. 22nd National Symposium on Wind Engineering, 61-66 (in Japanese). https://doi.org/10.14887/kazekosymp.22.0.61.0; Jiang, G., Yoshie, R. (2018). Large-eddy simulation of flow and pollutant dispersion in a 3D urban street model located in an unstable boundary layer. Build. Environ. 142, 47-57. https://doi.org/10.1016/j.buildenv.2018.06.015
  • Licence: CC BY 4.0

Cite

APA

Yoshie, R., Katada, K., Tominaga, Y., Kikumoto, H., & Okaze, T. (2025). AIJ UWE Benchmark Dataset – Case L (ArraysCT): Wind Tunnel Experiment for Flow and Dispersion around Cube Arrays with a Line-source under Non-isothermal Conditions [Data set]. Zenodo. https://doi.org/10.5281/zenodo.15487637

BibTeX

@misc{aijuwe_case_l,
  author    = "Yoshie, Ryuichiro and Katada, Koudai and Tominaga, Yoshihide and Kikumoto, Hideki and Okaze, Tsubasa",
  title     = "{AIJ UWE Benchmark Dataset -- Case L (ArraysCT): Wind Tunnel Experiment for Flow and Dispersion around Cube Arrays with a Line-source under Non-isothermal Conditions}",
  year      = "2025",
  publisher = "Zenodo",
  doi       = "10.5281/zenodo.15487637",
  url       = "https://doi.org/10.5281/zenodo.15487637",
  note      = "Data set"
}

API: see About.