Case I: reference data
Contents
Configuration
| Parameter | Value |
|---|---|
| Building | cube, 0.10 m on a side (= H) |
| Height H (m) | 0.1 |
| Reynolds number \(\mathrm{Re_H}\) | 11,000 |
| \(U_H\) (m/s) | 1.7 |
| \(U_H\), note | the readme and the velocity sheet; the approach flow at \(z = H\) is 1.6969 m/s and the workbook's inflow sheet divides by 1.697 |
| Wind directions (°) | 0 |
| source | 6 mm circular outlet at the centre of the roof (0, 0, 0.1); 10 % ethane in the mixture, 400 cc/min (= 6.67e-6 m³/s of mixture, 6.67e-7 m³/s of ethane); release velocity 0.236 m/s, M = \(V_e/U_H\) = 0.14 |
| reference concentration | \(c_0 = \dfrac{q}{U_H H^2}\) = 39.22 ppm (39.2 in the paper), q the ETHANE flow; concentration_ratio = \(C/c_0\) |
| Measurement planes | velocity: \(y/H = 0\) and \(z/H = 0.5\), concentration: \(y/H = 0\) and \(z/H = 0\) (the ground) |
| Points | Velocity: 91 concentration: 539 |
| Instrument | velocity: laser Doppler anemometer (Dantec BSA F60), 200 Hz, 240 s; concentration: hydrocarbon analyser (Kimoto HADA-01), 1 Hz, 120 s |
| Wind tunnel | AIST wind tunnel, 20 m long, 3.0 × 2.0 m cross-section; approach flow described as a 1/7 power law (data paper section 3.9) |
| Scale, note | model scale; the source states no model:full-scale ratio; Eddy3D solves it at 1:60 (a 6 m cube) |
Nomenclature: symbols, columns and scores
Geometry, reference scales and release
- \(H\), \(b\), \(D\) (m) — height of the building, cube, tower or tree belt; width of the building; edge of the cubes of Case C: the lengths the cases are drawn and normalised by
- \(U_H\) (m/s) — reference speed: the mean approach-flow speed at the height \(H\) (each Data page gives the value used)
- \(U_R\), \(H_R\), \(Z_R\) (m/s, m) — reference speed and height of a workbook: Case E, \(U_R\) at \(Z_R\) = 250 m full scale (1 m in the model); Case M, \(U_R\) and \(H_R\) at the reference point of the tunnel and of each field run
- \(U_{\mathrm{ref}}\), \(L_{\mathrm{ref}}\) (m/s, m) — reference speed and length of a case’s normalisation: \(U_H\) and \(H\) (\(U_R\) and \(H_R\) in Case M); for the velocity ratios the approach speed at 15.9 m (Case E) or at 500 m (Case F)
- \(U_b\) (m/s) — Case G: mean approach-flow speed at 9 m, the normalisation of its approach-flow table
- \(q\), \(c_{\mathrm{gas}}\) (m³/s, ppm) — tracer release of the experiment: volume flow of the released gas, and its tracer content (\(10^6\) ppm when pure); \(Q\) is the source strength given to a solve
- \(R_b\) (dimensionless) — bulk Richardson number of the heated-floor cases J and L (negative: unstable stratification)
- \(\mathrm{Re_H}\), \(\mathrm{Re_D}\) (dimensionless) — Reynolds numbers \(U_H H/\nu\) and \(U_H D/\nu\) (\(\nu\): kinematic viscosity of air)
- \(u_\ast\), \(z_0\), \(\kappa\) (m/s, mm, dimensionless) — friction velocity and roughness length of the log law fitted to the approach flow, and the von Kármán constant (0.41)
- \(\mathrm{WD}\) (column
wind_direction_deg; °) — wind direction (each frame says how it is counted); \(\mathrm{WD_R}\) is the mean direction of a field run at its reference point (Case M) - \(x\), \(y\), \(z\) (columns
x,y,z; m) — coordinates in the case’s frame (\(+x\), \(+y\) and \(+z\) are the positive directions; each Data page says which way \(+x\) points), \(z\) up from the floor of the tunnel or from the ground - \(\mathrm{d}x\) (m) — lattice spacing of the OpenLB and FluidX3D runs, in metres or as a fraction of \(H\) (\(H/64\))
- \(L_r\) (m) — reattachment length behind the building, read from a wake line at ground level; reported as \(L_r/H\)
Velocity and turbulence
- \(U\), \(V\), \(W\) (columns
U,V,W; m/s) — mean velocity along \(+x\), \(+y\), \(+z\); \(V\) is positive toward \(+y\) in every case - \(\lvert\mathbf{U}\rvert\) (m/s) — magnitude of the mean velocity vector, \(\sqrt{U^2+V^2+W^2}\)
- \(V_{\mathrm{s}}\) (column
Vs; m/s) — mean omnidirectional scalar speed of a thermistor (never a vector magnitude) - \(\overline{u'u'}\), \(\overline{v'v'}\), \(\overline{w'w'}\) (columns
uu,vv,ww; m²/s²) — velocity variances (overbar: time average, prime: fluctuation about it) - \(\overline{u'v'}\), \(\overline{u'w'}\), \(\overline{v'w'}\) (columns
uv,uw,vw; m²/s²) — Reynolds shear stresses - \(k = \tfrac{1}{2}\left(\overline{u'u'}+\overline{v'v'}+\overline{w'w'}\right)\) (column
k; m²/s²) — turbulent kinetic energy - \(U/U_{\mathrm{ref}}\) (column
velocity_ratio; dimensionless) — mean speed over the case’s reference speed (\(V_{\mathrm{s}}/U_{\mathrm{ref}}\) for a thermistor) - \(\sigma_{U/U_{\mathrm{ref}}}\) (column
velocity_ratio_sd; dimensionless) — standard deviation ofvelocity_ratioover the observations behind a field value (Case F) - \(k/U_{\mathrm{ref}}^2\) (column
k_ratio; dimensionless) — turbulent kinetic energy over the square of the reference speed, where only normalised values are published (Case G)
Concentration and temperature
- \(C\) (column
C; ppm) — mean tracer-gas concentration as published (volume fraction \(\times 10^6\) of the released gas diluted in air) - \(c_{\mathrm{rms}}\) (column
c_rms; ppm) — root mean square of the concentration fluctuation - \(c_0\) (ppm) — reference concentration, defined for each case on its Data page: \(c_0 = \dfrac{c_{\mathrm{gas}}\thinspace q}{U_H H^2}\) (\(U_R H_R^2\) in the denominator in Case M)
- \(c^\ast\) (column
concentration_ratio; dimensionless) — dimensionless concentration \(c^\ast = C/c_0\); the value of a solve is \(c\thinspace U_H H^2/Q\) for its mean concentration \(c\) and its source strength \(Q\) - \(\mathrm{Sc_t}\) (dimensionless) — turbulent Schmidt number of a solve (0.3, 0.5 and 0.7)
- \(T\), \(T_{\mathrm{rms}}\) (columns
T,T_rms; °C, K) — mean air temperature as published (Cases J and L) and the root mean square of its fluctuation - \(\overline{u'c'}\), \(\overline{v'c'}\), \(\overline{w'c'}\) (columns
uc,vc,wc; ppm·m/s) — turbulent concentration fluxes - \(\overline{u'\theta'}\), \(\overline{v'\theta'}\), \(\overline{w'\theta'}\) (columns
uT,vT,wT; K·m/s) — turbulent heat fluxes (\(\theta'\): the temperature fluctuation) - \(\theta = \dfrac{T_f - T}{T_f - T_H}\) (dimensionless) — floor-referenced temperature the solves of Cases J and L are scored on: 0 at the floor, 1 in the approach air at \(H\); \(T_f\) is the floor temperature and \(T_H\) the temperature of the approach flow at \(H\)
Scores
- \(n\) — number of pairs of a measured value \(o_i\) and a modelled value \(p_i\) at one point
- \(R\) — Pearson correlation coefficient of the pairs
- \(R^2\) — square of \(R\): share of the measured variance a linear fit to the model explains
- \(\mathrm{FAC2}\) — fraction of pairs with \(0.5 \le p_i/o_i \le 2\)
- \(\mathrm{FB}\) — fractional bias \(2(\overline{o}-\overline{p})/(\overline{o}+\overline{p})\), positive when the model is low
- \(\mathrm{HR}\) (hit rate) — fraction of pairs with \(\lvert p_i-o_i\rvert/\lvert o_i\rvert \le \delta_{\mathrm{rel}}\) or \(\lvert p_i-o_i\rvert \le \delta_{\mathrm{abs}}\), where \(\delta_{\mathrm{rel}} = 0.25\) and \(\delta_{\mathrm{abs}} = 0.05\thinspace U_H\) for a velocity component
- \(\mathrm{NMSE} = \dfrac{\overline{(o-p)^2}}{\overline{o}\thinspace \overline{p}}\) — normalised mean square error
- \(\mathrm{NAD} = \dfrac{\overline{\lvert o-p\rvert}}{\overline{o}+\overline{p}}\) — normalised absolute difference
- \(\mathrm{MG} = \exp\overline{(\ln o-\ln p)}\) — geometric mean bias
- \(\mathrm{VG} = \exp\overline{(\ln o-\ln p)^2}\) — geometric variance
- The ratio of \(\mathrm{FAC2}\) keeps its sign, so a model of the other sign than the measurement is a miss; \(\mathrm{FB}\), \(\mathrm{NMSE}\) and \(\mathrm{NAD}\) divide by the means, so they are undefined (shown as —) for a signed component unless the measured and the modelled mean are both positive
- VDI 3783-9 calls the hit rate \(q\) and the tolerances \(D\) and \(W\); on this site those letters keep their other meanings (\(q\) the tracer release rate, \(D\) the block size of Case C, \(W\) the vertical velocity)
- The detection limit of a concentration is one value per case, \(10^{-3}\) of the largest measured value. It sets \(\delta_{\mathrm{abs}}\) of the hit rate and the both-below rule of \(\mathrm{FAC2}\), and floors the values in \(\mathrm{MG}\) and \(\mathrm{VG}\).
- The scores \(\mathrm{FB}\), \(\mathrm{FAC2}\), \(\mathrm{NMSE}\), \(\mathrm{NAD}\), \(\mathrm{MG}\) and \(\mathrm{VG}\) follow Chang & Hanna (2004); the hit rate follows VDI 3783-9.
Quantities scored
- \(U\), \(V\) and \(W\) (mean velocity components) over \(U_H\)
- \(k\) (turbulent kinetic energy) over \(U_H^2\)
- the speed \(\lvert\mathbf{U}\rvert\) and \(\sqrt{\lvert\mathbf{U}\rvert^2+2k}\), against a thermistor’s \(V_{\mathrm{s}}\)
- \(c^\ast = C/c_0\) (dimensionless concentration) at turbulent Schmidt numbers \(\mathrm{Sc_t}\) of 0.3, 0.5 and 0.7
- \(\theta\) (floor-referenced temperature)
Frame and units
| Property | Definition |
|---|---|
| Origin | the centre of the cube on the ground plane |
| x | \(+x\) streamwise (the wind blows toward \(+x\)); the cube spans \(x \in \lbrack -0.05,\thinspace 0.05\rbrack\); wind points \(x = -0.15\thinspace\ldots\thinspace 0.25\thinspace\mathrm{m}\), concentration points \(x = 0.065\thinspace\ldots\thinspace 2.7\thinspace\mathrm{m}\) |
| y | \(+y\) lateral; the cube spans \(y \in \lbrack -0.05,\thinspace 0.05\rbrack\); concentration points reach \(\lvert y\rvert = 0.44\thinspace\mathrm{m}\) on the ground |
| z | \(+z\) up; roof at \(z = 0.1\thinspace\mathrm{m}\); the outlet at (0, 0, 0.1) |
| Lateral sign applied | 1 |
| Coordinate scale applied | 1.0 |
| Unit of length | m (model scale) |
| Unit of velocity | m/s |
| Unit of \(k\) | m²/s² |
| Unit of \(C\) | ppm |
| Unit of \(c^\ast\) | dimensionless, \(C/c_0\) |
Reference data
Source in this repository: raw/cases/case-i/RS-w_caseI.csv (approach flow: raw/cases/case-i/AF_caseI.csv).
The cleaned table has 630 rows over 630 distinct points; columns point_id, config, instrument, wind_direction_deg, x, y, z, U, V, W, k, campaign, C, concentration_ratio.
Unmeasured cells (null): U 539, V 592, W 539, k 539, C 91, concentration_ratio 91.
| Configuration | Points |
|---|---|
| default, wind tunnel, hydrocarbon analyser, WD 0° | 539 |
| default, wind tunnel, ldv, WD 0° | 91 |
Columns
The columns of the cleaned table (points.csv, points.json), in order.
The 14 columns and what each holds
| Column | Symbol | Meaning |
|---|---|---|
point_id | the tunnel's own measurement point number | |
config | configuration key: 'default', Case C centre building '0D'/'1D'/'2D', Case E state 'bc' (before) / 'ac' (after construction) | |
instrument | 'split_fibre' (vector components) or 'thermistor' (omnidirectional scalar speed) | |
wind_direction_deg | AIJ wind direction in degrees; 0 is the case's reference direction (see frame) | |
x | m, case frame | |
y | m, case frame | |
z | m above ground, case frame | |
U | \(U\) | m/s, mean velocity along \(+x\) |
V | \(V\) | m/s, mean velocity along \(+y\) (sign unified: positive toward \(+y\)) |
W | \(W\) | m/s, mean velocity along \(+z\) |
k | \(k\) | m²/s², turbulent kinetic energy |
campaign | 'wind_tunnel' (model scale) or 'field' (a full-scale observation: Cases F, G, M) | |
C | \(C\) | ppm, mean tracer-gas concentration as published (volume fraction x 1e6 of the released gas diluted in air) |
concentration_ratio | \(c^\ast\) | \(C/c_0\), \(c_0 = \dfrac{q}{U_{\mathrm{ref}} L_{\mathrm{ref}}^2}\) as the benchmark defines it for the case (manifest cases.<id>.normalisation) |
Inflow
| Property | Value |
|---|---|
| Method | log law, \(\kappa\) = 0.41, least squares over \(z = 0.02\thinspace\ldots\thinspace 0.4\thinspace\mathrm{m}\) on the workbook's 12-point approach profile |
| Friction velocity \(u_\ast\) (m/s) | 0.0928 |
| Roughness length \(z_0\) (mm) | 0.0455 |
| \(U_H\), measured (m/s) | 1.6969 |
| Log-law error at H | +2.6 % |
| power law index fitted | 0.115 |
| power law index paper | 1/7 |
| Note | derived during cleaning, not published by AIJ; the workbook's own \((z/H)^{1/7}\) column is within 4.6 % of the measured profile over \(z = 0.02\thinspace\ldots\thinspace 0.7\thinspace\mathrm{m}\) |
Known data issues
- \(V\) on the \(y = 0\) plane (53 of 91 points) is 0 in the CSV and 1e-9 … 4e-6 m/s in the workbook, a symmetry value. It is NaN in the table; \(V\) is measured only at the 38 off-plane points.
- The table carries the legacy workbook's values; the CSVs round to 3 decimals (velocity, \(k\)) and 1 decimal (concentration, ppm). Every concentration is a multiple of 0.1 ppm: a 0.4 ppm value carries +/-12 % of quantisation.
- The paper's \(c_0\) = 39.2 ppm needs the ETHANE flow (10 % of the 400 cc/min, 6.67e-7 m³/s); its sentence 'ethane released at 6.67e-6 m³/s' is the mixture. With the mixture flow \(c_0\) would be 392 ppm.
- The workbook normalises the approach flow with 1.697 m/s and the points with 1.7 m/s (0.18 % apart).
- AF_caseI.csv ends in 53 rows of ',,' and two stray cells, '0.5*' and '1.5*' (chart axis labels): a reader that does not test z for a number takes them for data.
- Thirteen ground-centreline locations (x, 0, 0) are measured twice (they are on both the \(y = 0\) and the \(z = 0\) plane) with values up to 8.5 % apart; both are kept. The four \(y = 0\), \(z = 0.05\) wind points that appear twice in the workbook are identical copies and appear once.
- Only the TKE is published, no variances and no concentration fluctuation: \(k\) cannot be checked against the components.
API
| Resource | Endpoint |
|---|---|
| Case | /api/cases/I.json |
| Points (JSON) | /api/cases/I/points.json |
| Points (CSV) | /api/cases/I/points.csv |
| Approach flow (CSV) | /api/cases/I/approach_flow.csv |
| Geometry | /api/cases/I/geometry.json |
| Geometry (STL) | /api/cases/I/geometry.stl |
| Validation | /api/cases/I/validation.json |
Attribution
- Data collected by Hiroaki Kondo (National Institute of Advanced Industrial Science and Technology), Katsuhiko Mutou (National Institute of Advanced Industrial Science and Technology) and Akihiro Hori (National Institute for Environmental Studies).
- Edited and distributed by Yoshihide Tominaga (Niigata Institute of Technology), Hideki Kikumoto (The University of Tokyo) and Tsubasa Okaze (Institute of Science Tokyo).
- DOI: 10.5281/zenodo.15430018
- Citation requested: Japan Society for Atmospheric Environment (2013). Guidelines for Atmospheric Environment Assessment Methods Using CFD Models (DiMCFD). Japan Society for Atmospheric Environment (in Japanese).
- Licence: CC BY 4.0
Cite
APA
Kondo, H., Mutou, K., Hori, A., Tominaga, Y., Kikumoto, H., & Okaze, T. (2025). AIJ UWE Benchmark Dataset – Case I (CubeC): Wind Tunnel Experiment for Flow and Dispersion around a Cubic Building Model [Data set]. Zenodo. https://doi.org/10.5281/zenodo.15430018
BibTeX
@misc{aijuwe_case_i,
author = "Kondo, Hiroaki and Mutou, Katsuhiko and Hori, Akihiro and Tominaga, Yoshihide and Kikumoto, Hideki and Okaze, Tsubasa",
title = "{AIJ UWE Benchmark Dataset -- Case I (CubeC): Wind Tunnel Experiment for Flow and Dispersion around a Cubic Building Model}",
year = "2025",
publisher = "Zenodo",
doi = "10.5281/zenodo.15430018",
url = "https://doi.org/10.5281/zenodo.15430018",
note = "Data set"
}
API: see About.