Case M: reference data
Contents
Configuration
| Parameter | Value |
|---|---|
| site | Tokyo Polytechnic University, Atsugi campus; terrain falls from about 32 m (campus plateau) to 3.6 m at the east edge; tallest building about 32 m |
| Scale | 1:600 |
| Points | 15 |
| Measurement height (m) | 3 |
| Measurement height, note | 3 m above the local ground, full scale (0.005 m model) |
| Wind directions (°) | 175, 180, 185 |
| wind direction velocity deg | 180 |
| field runs | 18 |
| field wind directions deg | 78 … 200.7 (mean direction at the reference point per run); 11 of 18 within 5° of 180° |
| reference | \(U\) R m s: 4.08 H R m model: 0.068 H R m full: 41 R: rooftop of the main building: the point is 41 m above the ground, 8 m above the roof in the STL |
| tracer | Wind tunnel: C2H4, 100 %, 6 mm outlet, 150 cc/min = 2.5e-6 m³/s (0.09 m/s) field: PMCH (C7F14), 200 ppm, 5 L/min, 1.5 m above ground, 25-26 Feb 2014, 18 runs of 10 min sampling |
| Normalisation | concentration ratio = \(C/c_0\), \(c_0 = \dfrac{q}{U_R H_R^2}\): 132.5 ppm in the tunnel (the paper rounds to 1.33e2); per run in the field (1,444 … 7,379 ppq) |
| Instrument | tunnel: DANTEC split-fibre probe (1000 Hz, 240 s) and high-speed hydrocarbon analyser; field: sorbent tubes with GC-ECD, sonic anemometer SAT-600 at the reference point |
| Wind tunnel | Eiffel-type boundary-layer wind tunnel, Tokyo Polytechnic University; cross-section 1.0 m high, 1.2 m wide; power law exponent 0.27 (AIJ Loads category IV) with an upwind taper for the topography |
Nomenclature: symbols, columns and scores
Geometry, reference scales and release
- \(H\), \(b\), \(D\) (m) — height of the building, cube, tower or tree belt; width of the building; edge of the cubes of Case C: the lengths the cases are drawn and normalised by
- \(U_H\) (m/s) — reference speed: the mean approach-flow speed at the height \(H\) (each Data page gives the value used)
- \(U_R\), \(H_R\), \(Z_R\) (m/s, m) — reference speed and height of a workbook: Case E, \(U_R\) at \(Z_R\) = 250 m full scale (1 m in the model); Case M, \(U_R\) and \(H_R\) at the reference point of the tunnel and of each field run
- \(U_{\mathrm{ref}}\), \(L_{\mathrm{ref}}\) (m/s, m) — reference speed and length of a case’s normalisation: \(U_H\) and \(H\) (\(U_R\) and \(H_R\) in Case M); for the velocity ratios the approach speed at 15.9 m (Case E) or at 500 m (Case F)
- \(U_b\) (m/s) — Case G: mean approach-flow speed at 9 m, the normalisation of its approach-flow table
- \(q\), \(c_{\mathrm{gas}}\) (m³/s, ppm) — tracer release of the experiment: volume flow of the released gas, and its tracer content (\(10^6\) ppm when pure); \(Q\) is the source strength given to a solve
- \(R_b\) (dimensionless) — bulk Richardson number of the heated-floor cases J and L (negative: unstable stratification)
- \(\mathrm{Re_H}\), \(\mathrm{Re_D}\) (dimensionless) — Reynolds numbers \(U_H H/\nu\) and \(U_H D/\nu\) (\(\nu\): kinematic viscosity of air)
- \(u_\ast\), \(z_0\), \(\kappa\) (m/s, mm, dimensionless) — friction velocity and roughness length of the log law fitted to the approach flow, and the von Kármán constant (0.41)
- \(\mathrm{WD}\) (column
wind_direction_deg; °) — wind direction (each frame says how it is counted); \(\mathrm{WD_R}\) is the mean direction of a field run at its reference point (Case M) - \(x\), \(y\), \(z\) (columns
x,y,z; m) — coordinates in the case’s frame (\(+x\), \(+y\) and \(+z\) are the positive directions; each Data page says which way \(+x\) points), \(z\) up from the floor of the tunnel or from the ground - \(\mathrm{d}x\) (m) — lattice spacing of the OpenLB and FluidX3D runs, in metres or as a fraction of \(H\) (\(H/64\))
- \(L_r\) (m) — reattachment length behind the building, read from a wake line at ground level; reported as \(L_r/H\)
Velocity and turbulence
- \(U\), \(V\), \(W\) (columns
U,V,W; m/s) — mean velocity along \(+x\), \(+y\), \(+z\); \(V\) is positive toward \(+y\) in every case - \(\lvert\mathbf{U}\rvert\) (m/s) — magnitude of the mean velocity vector, \(\sqrt{U^2+V^2+W^2}\)
- \(V_{\mathrm{s}}\) (column
Vs; m/s) — mean omnidirectional scalar speed of a thermistor (never a vector magnitude) - \(\overline{u'u'}\), \(\overline{v'v'}\), \(\overline{w'w'}\) (columns
uu,vv,ww; m²/s²) — velocity variances (overbar: time average, prime: fluctuation about it) - \(\overline{u'v'}\), \(\overline{u'w'}\), \(\overline{v'w'}\) (columns
uv,uw,vw; m²/s²) — Reynolds shear stresses - \(k = \tfrac{1}{2}\left(\overline{u'u'}+\overline{v'v'}+\overline{w'w'}\right)\) (column
k; m²/s²) — turbulent kinetic energy - \(U/U_{\mathrm{ref}}\) (column
velocity_ratio; dimensionless) — mean speed over the case’s reference speed (\(V_{\mathrm{s}}/U_{\mathrm{ref}}\) for a thermistor) - \(\sigma_{U/U_{\mathrm{ref}}}\) (column
velocity_ratio_sd; dimensionless) — standard deviation ofvelocity_ratioover the observations behind a field value (Case F) - \(k/U_{\mathrm{ref}}^2\) (column
k_ratio; dimensionless) — turbulent kinetic energy over the square of the reference speed, where only normalised values are published (Case G)
Concentration and temperature
- \(C\) (column
C; ppm) — mean tracer-gas concentration as published (volume fraction \(\times 10^6\) of the released gas diluted in air) - \(c_{\mathrm{rms}}\) (column
c_rms; ppm) — root mean square of the concentration fluctuation - \(c_0\) (ppm) — reference concentration, defined for each case on its Data page: \(c_0 = \dfrac{c_{\mathrm{gas}}\thinspace q}{U_H H^2}\) (\(U_R H_R^2\) in the denominator in Case M)
- \(c^\ast\) (column
concentration_ratio; dimensionless) — dimensionless concentration \(c^\ast = C/c_0\); the value of a solve is \(c\thinspace U_H H^2/Q\) for its mean concentration \(c\) and its source strength \(Q\) - \(\mathrm{Sc_t}\) (dimensionless) — turbulent Schmidt number of a solve (0.3, 0.5 and 0.7)
- \(T\), \(T_{\mathrm{rms}}\) (columns
T,T_rms; °C, K) — mean air temperature as published (Cases J and L) and the root mean square of its fluctuation - \(\overline{u'c'}\), \(\overline{v'c'}\), \(\overline{w'c'}\) (columns
uc,vc,wc; ppm·m/s) — turbulent concentration fluxes - \(\overline{u'\theta'}\), \(\overline{v'\theta'}\), \(\overline{w'\theta'}\) (columns
uT,vT,wT; K·m/s) — turbulent heat fluxes (\(\theta'\): the temperature fluctuation) - \(\theta = \dfrac{T_f - T}{T_f - T_H}\) (dimensionless) — floor-referenced temperature the solves of Cases J and L are scored on: 0 at the floor, 1 in the approach air at \(H\); \(T_f\) is the floor temperature and \(T_H\) the temperature of the approach flow at \(H\)
Scores
- \(n\) — number of pairs of a measured value \(o_i\) and a modelled value \(p_i\) at one point
- \(R\) — Pearson correlation coefficient of the pairs
- \(R^2\) — square of \(R\): share of the measured variance a linear fit to the model explains
- \(\mathrm{FAC2}\) — fraction of pairs with \(0.5 \le p_i/o_i \le 2\)
- \(\mathrm{FB}\) — fractional bias \(2(\overline{o}-\overline{p})/(\overline{o}+\overline{p})\), positive when the model is low
- \(\mathrm{HR}\) (hit rate) — fraction of pairs with \(\lvert p_i-o_i\rvert/\lvert o_i\rvert \le \delta_{\mathrm{rel}}\) or \(\lvert p_i-o_i\rvert \le \delta_{\mathrm{abs}}\), where \(\delta_{\mathrm{rel}} = 0.25\) and \(\delta_{\mathrm{abs}} = 0.05\thinspace U_H\) for a velocity component
- \(\mathrm{NMSE} = \dfrac{\overline{(o-p)^2}}{\overline{o}\thinspace \overline{p}}\) — normalised mean square error
- \(\mathrm{NAD} = \dfrac{\overline{\lvert o-p\rvert}}{\overline{o}+\overline{p}}\) — normalised absolute difference
- \(\mathrm{MG} = \exp\overline{(\ln o-\ln p)}\) — geometric mean bias
- \(\mathrm{VG} = \exp\overline{(\ln o-\ln p)^2}\) — geometric variance
- The ratio of \(\mathrm{FAC2}\) keeps its sign, so a model of the other sign than the measurement is a miss; \(\mathrm{FB}\), \(\mathrm{NMSE}\) and \(\mathrm{NAD}\) divide by the means, so they are undefined (shown as —) for a signed component unless the measured and the modelled mean are both positive
- VDI 3783-9 calls the hit rate \(q\) and the tolerances \(D\) and \(W\); on this site those letters keep their other meanings (\(q\) the tracer release rate, \(D\) the block size of Case C, \(W\) the vertical velocity)
- The detection limit of a concentration is one value per case, \(10^{-3}\) of the largest measured value. It sets \(\delta_{\mathrm{abs}}\) of the hit rate and the both-below rule of \(\mathrm{FAC2}\), and floors the values in \(\mathrm{MG}\) and \(\mathrm{VG}\).
- The scores \(\mathrm{FB}\), \(\mathrm{FAC2}\), \(\mathrm{NMSE}\), \(\mathrm{NAD}\), \(\mathrm{MG}\) and \(\mathrm{VG}\) follow Chang & Hanna (2004); the hit rate follows VDI 3783-9.
Quantities scored
- \(U\), \(V\) and \(W\) (mean velocity components) over \(U_H\)
- \(k\) (turbulent kinetic energy) over \(U_H^2\)
- the speed \(\lvert\mathbf{U}\rvert\) and \(\sqrt{\lvert\mathbf{U}\rvert^2+2k}\), against a thermistor’s \(V_{\mathrm{s}}\)
- \(c^\ast = C/c_0\) (dimensionless concentration) at turbulent Schmidt numbers \(\mathrm{Sc_t}\) of 0.3, 0.5 and 0.7
- \(\theta\) (floor-referenced temperature)
Frame and units
| Property | Definition |
|---|---|
| Origin | centre of the tunnel turntable on the floor plane (ground surface there at \(z = 33.07\thinspace\mathrm{m}\)) |
| x | \(+x\) NORTH (full-scale metres) |
| y | \(+y\) WEST (compass rose of MP_caseM.png: N at \(+x\), W at \(+y\)); the frame is right-handed |
| z | \(+z\) up from the TUNNEL FLOOR; the campus ground lies at z ~ 32 m |
| Wind direction convention | meteorological FROM-direction, so 180° blows toward \(+x\); flow_dir = (-cos WD, +sin WD), and a larger WD turns the plume toward -y. Measured on the tunnel's 175 / 180 / 185° and on the 18 field runs. |
| Lateral sign applied | 1 |
| Coordinate scale applied | 600.0 |
| Unit of length | m (FULL scale) |
| Unit of velocity | m/s (the tunnel's) |
| Unit of variance | m²/s² |
| Unit of concentration | ppm (the field's ppq converted) |
| Unit of \(c^\ast\) | dimensionless |
Reference data
Source in this repository: raw/cases/case-m/RS-WT_caseM.csv (approach flow: raw/cases/case-m/AF_caseM.csv).
The cleaned table has 330 rows over 15 distinct points; columns point_id, config, instrument, wind_direction_deg, x, y, z, U, V, W, uu, vv, ww, k, campaign, run, C, c_rms, concentration_ratio.
Unmeasured cells (null): U 315, V 315, W 315, uu 315, vv 315, ww 315, k 315, C 15, c_rms 285, concentration_ratio 15.
The 22 configurations and their points
| Configuration | Points |
|---|---|
| default, wind tunnel, hydrocarbon analyser, WD 175° | 15 |
| default, wind tunnel, hydrocarbon analyser, WD 180° | 15 |
| default, wind tunnel, hydrocarbon analyser, WD 185° | 15 |
| default, field, sorbent gc ecd, 9, WD 78° | 15 |
| default, field, sorbent gc ecd, 10, WD 115.667° | 15 |
| default, field, sorbent gc ecd, 1, WD 132.6° | 15 |
| default, field, sorbent gc ecd, 2, WD 144° | 15 |
| default, field, sorbent gc ecd, 11, WD 173.667° | 15 |
| default, field, sorbent gc ecd, 3, WD 175° | 15 |
| default, field, sorbent gc ecd, 13, WD 175.9° | 15 |
| default, field, sorbent gc ecd, 12, WD 176.7° | 15 |
| default, field, sorbent gc ecd, 15, WD 178.6° | 15 |
| default, field, sorbent gc ecd, 5, WD 179.6° | 15 |
| default, field, sorbent gc ecd, 14, WD 179.7° | 15 |
| default, field, sorbent gc ecd, 8, WD 180.3° | 15 |
| default, field, sorbent gc ecd, 4, WD 181.3° | 15 |
| default, field, sorbent gc ecd, 16, WD 181.9° | 15 |
| default, field, sorbent gc ecd, 7, WD 183.3° | 15 |
| default, field, sorbent gc ecd, 6, WD 184.3° | 15 |
| default, field, sorbent gc ecd, 17, WD 194.2° | 15 |
| default, field, sorbent gc ecd, 18, WD 200.7° | 15 |
| default, wind tunnel, split fibre, WD 180° | 15 |
Columns
The columns of the cleaned table (points.csv, points.json), in order.
The 19 columns and what each holds
| Column | Symbol | Meaning |
|---|---|---|
point_id | the tunnel's own measurement point number | |
config | configuration key: 'default', Case C centre building '0D'/'1D'/'2D', Case E state 'bc' (before) / 'ac' (after construction) | |
instrument | 'split_fibre' (vector components) or 'thermistor' (omnidirectional scalar speed) | |
wind_direction_deg | AIJ wind direction in degrees; 0 is the case's reference direction (see frame) | |
x | m, case frame | |
y | m, case frame | |
z | m above ground, case frame | |
U | \(U\) | m/s, mean velocity along \(+x\) |
V | \(V\) | m/s, mean velocity along \(+y\) (sign unified: positive toward \(+y\)) |
W | \(W\) | m/s, mean velocity along \(+z\) |
uu | \(\overline{u'u'}\) | m²/s², variance of u |
vv | \(\overline{v'v'}\) | m²/s², variance of v |
ww | \(\overline{w'w'}\) | m²/s², variance of w |
k | \(k\) | m²/s², turbulent kinetic energy |
campaign | 'wind_tunnel' (model scale) or 'field' (a full-scale observation: Cases F, G, M) | |
run | replicate label within a campaign where the dataset publishes individual runs (Case M); empty elsewhere | |
C | \(C\) | ppm, mean tracer-gas concentration as published (volume fraction x 1e6 of the released gas diluted in air) |
c_rms | \(c_{\mathrm{rms}}\) | ppm, rms of the concentration fluctuation |
concentration_ratio | \(c^\ast\) | \(C/c_0\), \(c_0 = \dfrac{q}{U_{\mathrm{ref}} L_{\mathrm{ref}}^2}\) as the benchmark defines it for the case (manifest cases.<id>.normalisation) |
Inflow
| Property | Value |
|---|---|
| Method | power law on the workbook's 40 heights (z 0.005 … 0.6 m model) at \(x = -0.498\thinspace\mathrm{m}\); the data paper states exponent 0.27 |
| Power-law exponent, fitted | 0.272 |
| Power-law exponent, data paper | 0.27 |
| \(U\) at R height m s | 3.94 |
| \(U\) R m s | 4.08 |
| Note | z is height above the empty tunnel floor; at the profile station the model's taper is already 0.052 m high, so the 10 lowest heights lie below it |
Known data issues
- Field concentrations are in ppq (1e-15 volume fraction) and the tunnel's in ppm: 1 ppq = 1e-9 ppm. The cleaned table converts the field's to ppm and carries \(C/c_0\) for both, with the run's own \(c_0\) in the field.
- Every field run has its own reference speed \(U_R\), mean direction \(\mathrm{WD_R}\) and tracer flow q (clean/manifest.json -> cases.M.extra_measurements.field_runs); the row's wind_direction_deg is \(\mathrm{WD_R}\).
- The tunnel measured velocity only at 180°; at 175° and 185° the CSV has -999.9 in all seven velocity columns.
- RS-WT_caseM.csv is the legacy workbook rounded (2 dp velocity, 1 dp concentration), and its \(k\) is half the sum of the 2-dp RMS values, up to 0.005 m2/s2 from the workbook's; the cleaned table carries the workbook's values.
- The tunnel source is on the ground in the workbook, LC_caseM.csv and the STL (readme: 'on a rooftop'); the field source was 1.5 m above ground.
- \(H_R\) = 41 m is the anemometer height above the ground; the main roof under the reference point is about 33 m above it. \(c_0\) uses \(H_R\) = 0.068 m (41 m / 600 = 0.06833 m would give 131.2 ppm, -1 %).
- The field has an ambient floor of 8 - 11 ppq at points 11 - 15 in every run (not subtracted); the tunnel's concentration has a zero offset (two negative means at point 12) and an rms floor of 7 ppm.
- Only 11 of the 18 field runs are within 5° of 180°, the tunnel's direction; runs 1, 2 and 9 have \(U_R\) of 1.4 - 1.8 m/s.
- BD_caseM.stl is MODEL scale, wound inward on its ground and roof facets, and has 21 boundary and 7 non-manifold edges (7 on the rim of the panel, 14 on 7 slivers hanging on building roofs); the served geometry.stl is multiplied by 600, re-wound outward, without the slivers and closed with a base slab down to \(z = -1\thinspace\mathrm{m}\).
- The approach-flow heights are above the empty tunnel floor: at the profile station the model's taper is 0.052 m high, above the 10 lowest profile heights.
API
| Resource | Endpoint |
|---|---|
| Case | /api/cases/M.json |
| Points (JSON) | /api/cases/M/points.json |
| Points (CSV) | /api/cases/M/points.csv |
| Approach flow (CSV) | /api/cases/M/approach_flow.csv |
| Geometry | /api/cases/M/geometry.json |
| Geometry (STL) | /api/cases/M/geometry.stl |
| Validation | /api/cases/M/validation.json |
Attribution
- Data collected by Ryuichiro Yoshie (Tokyo Polytechnic University) and Takumi Tachibana (Wind Engineering Institute).
- Edited and distributed by Yoshihide Tominaga (Niigata Institute of Technology), Hideki Kikumoto (The University of Tokyo) and Tsubasa Okaze (Institute of Science Tokyo).
- DOI: 10.5281/zenodo.15487857
- Citation requested: Tachibana, T., Yoshie, R., Nakayama, S., Kishida, T., Miyashita, K., Sasaki, R. (2022). Comparison between field measurement and wind tunnel experiments of gas dispersion in an urban area and verification of similarity law. Journal of Wind Engineering 47(3), 39-52 (in Japanese). http://dx.doi.org/10.5359/jwe.47.39
- Licence: CC BY 4.0
Cite
APA
Yoshie, R., Tachibana, T., Tominaga, Y., Kikumoto, H., & Okaze, T. (2025). AIJ UWE Benchmark Dataset – Case M (TPU): Wind Tunnel Experiment and Field Observation for Flow and Dispersion within TPU Campus [Data set]. Zenodo. https://doi.org/10.5281/zenodo.15487857
BibTeX
@misc{aijuwe_case_m,
author = "Yoshie, Ryuichiro and Tachibana, Takumi and Tominaga, Yoshihide and Kikumoto, Hideki and Okaze, Tsubasa",
title = "{AIJ UWE Benchmark Dataset -- Case M (TPU): Wind Tunnel Experiment and Field Observation for Flow and Dispersion within TPU Campus}",
year = "2025",
publisher = "Zenodo",
doi = "10.5281/zenodo.15487857",
url = "https://doi.org/10.5281/zenodo.15487857",
note = "Data set"
}
API: see About.