Case F: reference data
Contents
Configuration
| Parameter | Value |
|---|---|
| District | Shinjuku sub-centre during construction of the high-rise group, building configuration of November 1978 |
| Scale | 1:800 |
| model | terrain and buildings in a disc of radius 725 m (BD_caseF.stl; the readme and the data paper say 800 m / 1600 m diameter) |
| Points | 13 |
| point numbers | 1-3, 5-11, 13-15 (4 and 12 absent; points 16 and later belong to later construction stages and are not in the dataset) |
| Wind directions | N, NNE, NE, ENE, SE, SSE, S, SSW, SW, WNW, NW, NNW |
| wind directions field | N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, \(W\), WNW, NW, NNW |
| measurement planes above ground m | 5, 9, 20 |
| measurement planes z m | 15, 19, 30 |
| ground offset m | 10 |
| Normalisation | velocity ratio = mean speed / the approaching mean speed at the boundary-layer height 500 m (full scale); the field values were converted to it with the tunnel (readme). \(U(500\text{ m})\) is 10 m/s in the data paper and 10.65 m/s implied by the profile |
| Instrument | tunnel: thermistor anemometer, 30 s averaging; field: three-cup anemometer with wind vane, 10-minute means above 5 m/s at the reference roof, December 1977 - November 1978 |
| Wind tunnel | Shimizu Corporation wind tunnel; cross-section 1.55 m wide, 2.2 m high; power-law inflow, exponent 1/4 |
| reference roofs | SMB: Shinjuku-Mitsui Building, roof G.L.+210 m, anemometer G.L.+237 m, for NW-NE KDD: KDD Building, roof G.L.+165 m, anemometer G.L.+187 m, for the other directions |
Nomenclature: symbols, columns and scores
Geometry, reference scales and release
- \(H\), \(b\), \(D\) (m) — height of the building, cube, tower or tree belt; width of the building; edge of the cubes of Case C: the lengths the cases are drawn and normalised by
- \(U_H\) (m/s) — reference speed: the mean approach-flow speed at the height \(H\) (each Data page gives the value used)
- \(U_R\), \(H_R\), \(Z_R\) (m/s, m) — reference speed and height of a workbook: Case E, \(U_R\) at \(Z_R\) = 250 m full scale (1 m in the model); Case M, \(U_R\) and \(H_R\) at the reference point of the tunnel and of each field run
- \(U_{\mathrm{ref}}\), \(L_{\mathrm{ref}}\) (m/s, m) — reference speed and length of a case’s normalisation: \(U_H\) and \(H\) (\(U_R\) and \(H_R\) in Case M); for the velocity ratios the approach speed at 15.9 m (Case E) or at 500 m (Case F)
- \(U_b\) (m/s) — Case G: mean approach-flow speed at 9 m, the normalisation of its approach-flow table
- \(q\), \(c_{\mathrm{gas}}\) (m³/s, ppm) — tracer release of the experiment: volume flow of the released gas, and its tracer content (\(10^6\) ppm when pure); \(Q\) is the source strength given to a solve
- \(R_b\) (dimensionless) — bulk Richardson number of the heated-floor cases J and L (negative: unstable stratification)
- \(\mathrm{Re_H}\), \(\mathrm{Re_D}\) (dimensionless) — Reynolds numbers \(U_H H/\nu\) and \(U_H D/\nu\) (\(\nu\): kinematic viscosity of air)
- \(u_\ast\), \(z_0\), \(\kappa\) (m/s, mm, dimensionless) — friction velocity and roughness length of the log law fitted to the approach flow, and the von Kármán constant (0.41)
- \(\mathrm{WD}\) (column
wind_direction_deg; °) — wind direction (each frame says how it is counted); \(\mathrm{WD_R}\) is the mean direction of a field run at its reference point (Case M) - \(x\), \(y\), \(z\) (columns
x,y,z; m) — coordinates in the case’s frame (\(+x\), \(+y\) and \(+z\) are the positive directions; each Data page says which way \(+x\) points), \(z\) up from the floor of the tunnel or from the ground - \(\mathrm{d}x\) (m) — lattice spacing of the OpenLB and FluidX3D runs, in metres or as a fraction of \(H\) (\(H/64\))
- \(L_r\) (m) — reattachment length behind the building, read from a wake line at ground level; reported as \(L_r/H\)
Velocity and turbulence
- \(U\), \(V\), \(W\) (columns
U,V,W; m/s) — mean velocity along \(+x\), \(+y\), \(+z\); \(V\) is positive toward \(+y\) in every case - \(\lvert\mathbf{U}\rvert\) (m/s) — magnitude of the mean velocity vector, \(\sqrt{U^2+V^2+W^2}\)
- \(V_{\mathrm{s}}\) (column
Vs; m/s) — mean omnidirectional scalar speed of a thermistor (never a vector magnitude) - \(\overline{u'u'}\), \(\overline{v'v'}\), \(\overline{w'w'}\) (columns
uu,vv,ww; m²/s²) — velocity variances (overbar: time average, prime: fluctuation about it) - \(\overline{u'v'}\), \(\overline{u'w'}\), \(\overline{v'w'}\) (columns
uv,uw,vw; m²/s²) — Reynolds shear stresses - \(k = \tfrac{1}{2}\left(\overline{u'u'}+\overline{v'v'}+\overline{w'w'}\right)\) (column
k; m²/s²) — turbulent kinetic energy - \(U/U_{\mathrm{ref}}\) (column
velocity_ratio; dimensionless) — mean speed over the case’s reference speed (\(V_{\mathrm{s}}/U_{\mathrm{ref}}\) for a thermistor) - \(\sigma_{U/U_{\mathrm{ref}}}\) (column
velocity_ratio_sd; dimensionless) — standard deviation ofvelocity_ratioover the observations behind a field value (Case F) - \(k/U_{\mathrm{ref}}^2\) (column
k_ratio; dimensionless) — turbulent kinetic energy over the square of the reference speed, where only normalised values are published (Case G)
Concentration and temperature
- \(C\) (column
C; ppm) — mean tracer-gas concentration as published (volume fraction \(\times 10^6\) of the released gas diluted in air) - \(c_{\mathrm{rms}}\) (column
c_rms; ppm) — root mean square of the concentration fluctuation - \(c_0\) (ppm) — reference concentration, defined for each case on its Data page: \(c_0 = \dfrac{c_{\mathrm{gas}}\thinspace q}{U_H H^2}\) (\(U_R H_R^2\) in the denominator in Case M)
- \(c^\ast\) (column
concentration_ratio; dimensionless) — dimensionless concentration \(c^\ast = C/c_0\); the value of a solve is \(c\thinspace U_H H^2/Q\) for its mean concentration \(c\) and its source strength \(Q\) - \(\mathrm{Sc_t}\) (dimensionless) — turbulent Schmidt number of a solve (0.3, 0.5 and 0.7)
- \(T\), \(T_{\mathrm{rms}}\) (columns
T,T_rms; °C, K) — mean air temperature as published (Cases J and L) and the root mean square of its fluctuation - \(\overline{u'c'}\), \(\overline{v'c'}\), \(\overline{w'c'}\) (columns
uc,vc,wc; ppm·m/s) — turbulent concentration fluxes - \(\overline{u'\theta'}\), \(\overline{v'\theta'}\), \(\overline{w'\theta'}\) (columns
uT,vT,wT; K·m/s) — turbulent heat fluxes (\(\theta'\): the temperature fluctuation) - \(\theta = \dfrac{T_f - T}{T_f - T_H}\) (dimensionless) — floor-referenced temperature the solves of Cases J and L are scored on: 0 at the floor, 1 in the approach air at \(H\); \(T_f\) is the floor temperature and \(T_H\) the temperature of the approach flow at \(H\)
Scores
- \(n\) — number of pairs of a measured value \(o_i\) and a modelled value \(p_i\) at one point
- \(R\) — Pearson correlation coefficient of the pairs
- \(R^2\) — square of \(R\): share of the measured variance a linear fit to the model explains
- \(\mathrm{FAC2}\) — fraction of pairs with \(0.5 \le p_i/o_i \le 2\)
- \(\mathrm{FB}\) — fractional bias \(2(\overline{o}-\overline{p})/(\overline{o}+\overline{p})\), positive when the model is low
- \(\mathrm{HR}\) (hit rate) — fraction of pairs with \(\lvert p_i-o_i\rvert/\lvert o_i\rvert \le \delta_{\mathrm{rel}}\) or \(\lvert p_i-o_i\rvert \le \delta_{\mathrm{abs}}\), where \(\delta_{\mathrm{rel}} = 0.25\) and \(\delta_{\mathrm{abs}} = 0.05\thinspace U_H\) for a velocity component
- \(\mathrm{NMSE} = \dfrac{\overline{(o-p)^2}}{\overline{o}\thinspace \overline{p}}\) — normalised mean square error
- \(\mathrm{NAD} = \dfrac{\overline{\lvert o-p\rvert}}{\overline{o}+\overline{p}}\) — normalised absolute difference
- \(\mathrm{MG} = \exp\overline{(\ln o-\ln p)}\) — geometric mean bias
- \(\mathrm{VG} = \exp\overline{(\ln o-\ln p)^2}\) — geometric variance
- The ratio of \(\mathrm{FAC2}\) keeps its sign, so a model of the other sign than the measurement is a miss; \(\mathrm{FB}\), \(\mathrm{NMSE}\) and \(\mathrm{NAD}\) divide by the means, so they are undefined (shown as —) for a signed component unless the measured and the modelled mean are both positive
- VDI 3783-9 calls the hit rate \(q\) and the tolerances \(D\) and \(W\); on this site those letters keep their other meanings (\(q\) the tracer release rate, \(D\) the block size of Case C, \(W\) the vertical velocity)
- The detection limit of a concentration is one value per case, \(10^{-3}\) of the largest measured value. It sets \(\delta_{\mathrm{abs}}\) of the hit rate and the both-below rule of \(\mathrm{FAC2}\), and floors the values in \(\mathrm{MG}\) and \(\mathrm{VG}\).
- The scores \(\mathrm{FB}\), \(\mathrm{FAC2}\), \(\mathrm{NMSE}\), \(\mathrm{NAD}\), \(\mathrm{MG}\) and \(\mathrm{VG}\) follow Chang & Hanna (2004); the hit rate follows VDI 3783-9.
Quantities scored
- \(U\), \(V\) and \(W\) (mean velocity components) over \(U_H\)
- \(k\) (turbulent kinetic energy) over \(U_H^2\)
- the speed \(\lvert\mathbf{U}\rvert\) and \(\sqrt{\lvert\mathbf{U}\rvert^2+2k}\), against a thermistor’s \(V_{\mathrm{s}}\)
- \(c^\ast = C/c_0\) (dimensionless concentration) at turbulent Schmidt numbers \(\mathrm{Sc_t}\) of 0.3, 0.5 and 0.7
- \(\theta\) (floor-referenced temperature)
Frame and units
| Property | Definition |
|---|---|
| Origin | centre of the reproduced district, tunnel floor plane |
| x | \(+x\) EAST (full-scale metres) |
| y | \(+y\) NORTH (compass rose in MP_caseF.png) |
| z | \(+z\) up from the TUNNEL FLOOR; the readme's rule is ground = z - 10 m (the STL's terrain under the points is at \(z = 5\thinspace\mathrm{m}\)) |
| Wind direction convention | compass FROM-direction (N = 0, E = 90), so N blows toward -y; flow_dir = (-sin WD, -cos WD). Not stated by the sources; supported by the reference-building choice and by upwind roughness, and at NNW by a solved field (status 'corroborated by a solved field'; the other directions stay 'unverified'). |
| Lateral sign applied | 1 |
| Coordinate scale applied | 800.0 |
| Unit of length | m (FULL scale) |
| Unit of \(U/U_{\mathrm{ref}}\) | dimensionless |
| Unit of \(\sigma_{U/U_{\mathrm{ref}}}\) | dimensionless |
Reference data
Source in this repository: raw/cases/case-f/RS-WT_caseF.csv (approach flow: raw/cases/case-f/AF_caseF.csv).
The cleaned table has 472 rows over 13 distinct points; columns point_id, config, instrument, wind_direction, wind_direction_deg, x, y, z, velocity_ratio, campaign, velocity_ratio_sd.
Unmeasured cells (null): velocity_ratio_sd 264.
The 40 configurations and their points
| Configuration | Points |
|---|---|
| default, field, cup anemometer, N, WD 0° | 13 |
| default, field, cup anemometer, NNE, WD 22.5° | 13 |
| default, field, cup anemometer, NE, WD 45° | 13 |
| default, field, cup anemometer, ENE, WD 67.5° | 13 |
| default, field, cup anemometer, E, WD 90° | 13 |
| default, field, cup anemometer, ESE, WD 112.5° | 13 |
| default, field, cup anemometer, SE, WD 135° | 13 |
| default, field, cup anemometer, SSE, WD 157.5° | 13 |
| default, field, cup anemometer, S, WD 180° | 13 |
| default, field, cup anemometer, SSW, WD 202.5° | 13 |
| default, field, cup anemometer, SW, WD 225° | 13 |
| default, field, cup anemometer, WSW, WD 247.5° | 13 |
| default, field, cup anemometer, W, WD 270° | 13 |
| default, field, cup anemometer, WNW, WD 292.5° | 13 |
| default, field, cup anemometer, NW, WD 315° | 13 |
| default, field, cup anemometer, NNW, WD 337.5° | 13 |
| default, wind tunnel, thermistor, N, WD 0° | 13 |
| default, wind tunnel, thermistor, NNE, WD 22.5° | 13 |
| default, wind tunnel, thermistor, NE, WD 45° | 13 |
| default, wind tunnel, thermistor, ENE, WD 67.5° | 13 |
| default, wind tunnel, thermistor, SE, WD 135° | 13 |
| default, wind tunnel, thermistor, SSE, WD 157.5° | 13 |
| default, wind tunnel, thermistor, S, WD 180° | 13 |
| default, wind tunnel, thermistor, SSW, WD 202.5° | 13 |
| default, wind tunnel, thermistor, SW, WD 225° | 13 |
| default, wind tunnel, thermistor, WNW, WD 292.5° | 13 |
| default, wind tunnel, thermistor, NW, WD 315° | 13 |
| default, wind tunnel, thermistor, NNW, WD 337.5° | 13 |
| h20, wind tunnel, thermistor, N, WD 0° | 9 |
| h20, wind tunnel, thermistor, NNE, WD 22.5° | 13 |
| h20, wind tunnel, thermistor, ENE, WD 67.5° | 12 |
| h20, wind tunnel, thermistor, S, WD 180° | 11 |
| h20, wind tunnel, thermistor, SSW, WD 202.5° | 12 |
| h20, wind tunnel, thermistor, SW, WD 225° | 9 |
| h20, wind tunnel, thermistor, NNW, WD 337.5° | 13 |
| h5, wind tunnel, thermistor, NNE, WD 22.5° | 4 |
| h5, wind tunnel, thermistor, ENE, WD 67.5° | 8 |
| h5, wind tunnel, thermistor, S, WD 180° | 5 |
| h5, wind tunnel, thermistor, SSW, WD 202.5° | 5 |
| h5, wind tunnel, thermistor, NNW, WD 337.5° | 7 |
Columns
The columns of the cleaned table (points.csv, points.json), in order.
The 11 columns and what each holds
| Column | Symbol | Meaning |
|---|---|---|
point_id | the tunnel's own measurement point number | |
config | configuration key: 'default', Case C centre building '0D'/'1D'/'2D', Case E state 'bc' (before) / 'ac' (after construction) | |
instrument | 'split_fibre' (vector components) or 'thermistor' (omnidirectional scalar speed) | |
wind_direction | compass name of the direction the wind comes FROM (Case E) | |
wind_direction_deg | AIJ wind direction in degrees; 0 is the case's reference direction (see frame) | |
x | m, case frame | |
y | m, case frame | |
z | m above ground, case frame | |
velocity_ratio | \(U/U_{\mathrm{ref}}\) | dimensionless, mean speed over the case's reference speed (Case E: \(V_{\mathrm{s}}/U(15.9\text{ m})\), \(U(15.9\text{ m})\) = 3.935 m/s; see the case's normalisation) |
campaign | 'wind_tunnel' (model scale) or 'field' (a full-scale observation: Cases F, G, M) | |
velocity_ratio_sd | \(\sigma_{U/U_{\mathrm{ref}}}\) | standard deviation of velocity_ratio over the observations behind a field value (Case F) |
Inflow
| Property | Value |
|---|---|
| Method | power law on the 18 published heights (z 10 … 400 m full scale); the data paper states exponent 1/4 |
| Power-law exponent, fitted | 0.277 |
| Power-law exponent, data paper | 0.25 |
| \(U\) 500m m s | data paper: 10.0 implied by profile: 10.65 |
| Note | AF_caseF.csv stops at 400 m (\(U\) = 10.0 m/s); the workbook's \(U/U_R\) profile (0.94 at 400 m) puts the 500 m speed at 10.65 m/s |
Known data issues
- The 16 field rows of point 14 in RS-FO_caseF.csv hold the workbook's value of the NEXT wind direction clockwise (the series is shifted by one); the cleaned table follows the workbook (clean/QUESTIONS.md QF1).
- Tunnel and STL coordinates are MODEL scale (1:800); the field's are full scale. The case frame is full scale; the tunnel's \(x\), \(y\), \(z\) and the STL are multiplied by 800.
- z is height above the tunnel floor. The readme's rule 'ground = z - 10 m' gives the 5 / 9 / 20 m planes, but the STL's terrain under all 13 points is at \(z = 5\thinspace\mathrm{m}\), so the planes stand 10 / 14 / 25 m above it.
- BD_caseF.stl is wound inward on every ground, roof and sampled wall facet and is open along the rim of its 725 m disc (812 boundary edges); the served geometry.stl is re-wound outward and closed with a base slab down to \(z = -1\thinspace\mathrm{m}\).
- MP_caseF.csv names the two reference points the other way round from the workbook, the STL and MP_caseF.png (the workbook's Shinjuku-Mitsui Building is the 225 m tower at (-17.5, 96.0), the KDD Building the 180 m one at (85.8, -347.1)).
- Field values are the legacy workbook's roof-anemometer ratios times 0.940 (NW-NE) or 0.963 (other directions); sigma is the workbook's S.D. rounded to 0.01 times that factor, so it moves in steps of 0.0094 / 0.0096.
- The tunnel did not run E, ESE, WSW or W; the field data cover all 16. The 5 m and 20 m planes exist at some points only (29 and 79 rows).
- One tunnel value (point 8, SW, 9 m: 0.474) has no counterpart in the workbook's results sheet, and the flat 'Sheet1' table has 0.63 there.
- Field anemometer heights above the tunnel floor are 13 - 21 m (3 - 11 m above ground by the readme's rule); the data paper says 3 - 9 m, so points 13 and 14 (11 m) disagree.
- The thermistor reads a SCALAR speed and the cup anemometer a 10-minute mean: a RANS \(\lvert\mathbf{U}\rvert\) is biased low against both.
- The files do not say whether a wind direction names where the wind comes from. The cleaned tables read it as the direction the wind comes from (N = 0, E = 90). At NNW a solved field supports that reading: Eddy3D's OpenFOAM 12 run for the wind from NNW correlates R 0.935 with the tunnel's 9 m column labelled NNW and R 0.077 with its column labelled SSE, the opposite wind (clean/QUESTIONS.md QF9); the other directions are not solved and stay unverified.
API
| Resource | Endpoint |
|---|---|
| Case | /api/cases/F.json |
| Points (JSON) | /api/cases/F/points.json |
| Points (CSV) | /api/cases/F/points.csv |
| Approach flow (CSV) | /api/cases/F/approach_flow.csv |
| Geometry | /api/cases/F/geometry.json |
| Geometry (STL) | /api/cases/F/geometry.stl |
| Validation | /api/cases/F/validation.json |
Attribution
- Data collected by K. Fujii, Y. Asami, Y. Iwasa et al. (the original 1978 investigation; the readme names no data collectors).
- Edited and distributed by Yoshihide Tominaga (Niigata Institute of Technology), Hideki Kikumoto (The University of Tokyo) and Tsubasa Okaze (Institute of Science Tokyo).
- DOI: 10.5281/zenodo.15589621
- Citation requested: Fujii, K., Asami, Y., Iwasa, Y. et al. (1978). Wind in Shinjuku Sub-Central Area — Comparison Between Field Measurement and Wind Tunnel Experiment. Proc. 5th Symposium on Wind Resistance of Structures, 91-98 (in Japanese).
- Licence: CC BY 4.0
Cite
APA
Tominaga, Y., Kikumoto, H., & Okaze, T. (2025). AIJ UWE Benchmark Dataset – Case F (Shinjuku): Wind Tunnel Experiment and Field Observation for Flow within an Actual Urban Area in Shinjuku [Data set]. Zenodo. https://doi.org/10.5281/zenodo.15589621
BibTeX
@misc{aijuwe_case_f,
author = "Tominaga, Yoshihide and Kikumoto, Hideki and Okaze, Tsubasa",
title = "{AIJ UWE Benchmark Dataset -- Case F (Shinjuku): Wind Tunnel Experiment and Field Observation for Flow within an Actual Urban Area in Shinjuku}",
year = "2025",
publisher = "Zenodo",
doi = "10.5281/zenodo.15589621",
url = "https://doi.org/10.5281/zenodo.15589621",
note = "Data set"
}
API: see About.